96 mhz saw filter 20 mhz bandwidth part number: SF0096BA02458S spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0096BA02458S rev a 22-feb-2010 ecn 36650 page 1 of 3 description ? 96 mhz saw bandpass filter with 20 mhz bandwidth. ? 5 x 7 mm smp. ? rohs compliant. typical performance horizontal: frequency : 10 mhz/div vertical from top: relative magnitude : 10 db/div relative magnitude : 1 db/div phase linearity : 5 deg/div group delay deviation : 100 ns/div s11 s22
96 mhz saw filter 20 mhz bandwidth part number: SF0096BA02458S spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0096BA02458S rev a 22-feb-2010 ecn 36650 page 2 of 3 specification parameter min typ max units center frequency, f c 1 - 96.00 - mhz insertion loss (86-106 mhz) 1,2 - 11.3 13 db 1 db bandwidth 20.0 23.4 - mhz relative attenuation to ins loss (0.3-68.4 mhz) 1,3 50 55 - db relative attenuation to ins loss (at 76.8 mhz) 1,3 45 50 - db relative attenuation to ins loss (123.6 to 162.8 mhz) 1,3 40 48 - db relative attenuation to ins loss (162.8 to 240 mhz) 1,3 35 53 - db relative attenuation to ins loss (240 to 1000 mhz) 1,3 25 35 - db amplitude ripple (86 to 106 mhz) 1,4 - 0.75 1 db p-p group delay ripple (86 to 106 mhz) 1,5 50 60 ns/div 1 db compression point (86 to 106 mhz) 12 15 - dbm input ip3 6 35 40 - dbm temperature coefficient - 94 - ppm/ ? c source/load impedance 50 ohms ambient temperature - 25 - ? c notes: 1. measured with terminating impedance matched to 50 ? and with 50 ? analyzer. 2. average insertion loss in indicated frequency range. 3. measured as attenuation below the insert ion loss point (insertion loss is reference). 4. amplitude ripple should be measured without smoothing. 5. group delay ripple may be measured with a smoothing aperture of 250 khz . 6. by design. maximum ratings parameter min max units storage temperature range -40 85 ? c operating temperature range -25 85 ? c input power level - 12 dbm matching circuit typical component values: notes: 1. recommend use of 2% tolerance matching components. 2. component values are for reference only and may change depending on board layout. ls1 = 220 nh ls2 = 82 nh lp1 = 270 nh rp2 = 680 ? 10 4 all others input 50 ? single-ended output 50 ? single-ended gnd
96 mhz saw filter 20 mhz bandwidth part number: SF0096BA02458S spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0096BA02458S rev a 22-feb-2010 ecn 36650 page 3 of 3 package outline suggested footprint iso 9001 registered all specifications are believed to be accurate and reliable. howe ver, spectrum microwave reserves the right to make changes wit hout notice. ? 2010 all rights reserved. package material: body: al 2 o 3 ceramic lid: kovar, ni plated terminations: au plating 1 m min, over a 1.3-8.9 m ni plating units: mm tolerances are 0.15 mm except for the overall length and width, which are nominal values. pad configuration: input: 10 output: 4 ground: all other pads
|
